Concrete Contractor in Colton, CA - Driveways and Slabs on a Solid Base
Bedrock Moreno Valley Concrete Company is a concrete contractor pouring driveways, patios, steps and slab foundations for homes and small properties in Colton, CA. I look at every job myself, and our crew forms and finishes the pour.
Pouring concrete in Colton
Colton sits between Riverside and San Bernardino, a short drive from our base in Moreno Valley, and its streets mix older homes, newer houses and small businesses. Most of what we see here is worn driveways, cracked patios, walks that have dropped and garage slabs, the same work we do in cities like San Jacinto.
On a Colton job, the price moves with the size of the slab, whether old concrete has to be broken out and hauled away, and how much digging and packing the subgrade needs, which is the dirt the slab sits on. The schedule depends on whether the city wants a permit and inspections, and on curing, the wait while new concrete hardens before it takes weight, which isn't worth rushing. You'll get your own figure when I come out and look. The ground deserves a word too. The San Jacinto fault zone runs right through Colton, and the city's safety plan maps ground prone to liquefaction along both banks of the Santa Ana River and in the Reche Canyon areas. That's where loose, wet soil can act like liquid in a hard shake. Nobody can pour an earthquake-proof driveway, but on ground like that, what's under the slab matters more than what's on top.
Concrete work we do in Colton
Older driveways around Colton often crack and settle because the base was never packed, so we tear them out, dig down to firm ground and pour new.
Plenty of Colton backyards have a cracked slab or bare dirt off the back door. We pour patios sloped so water runs to the yard, not the house.
Stamped concrete gives a Colton front walk or patio the look of stone or brick, pressed in while it's soft, with less upkeep than pavers.
When a walkway has heaved or dropped into a trip hazard, we replace the bad sections and cut grooves so the next crack lands where we planned.
Garage floors take car weight, oil and tools, so we break out a sunken floor and pour new with rebar, steel bars that keep cracks from pulling apart.
Decorative work covers color, exposed stone and saw-cut patterns on plain concrete, and it's a good way to dress up an older Colton front yard without a full tear-out.
Where a yard steps up or down, a concrete wall holds the dirt back. We build in drainage behind it, since trapped water is what pushes walls over.
For shops, sheds and work buildings on Colton lots, we pour interior floors flat and smooth, ready for racks, equipment and daily use.
A Colton backyard pool deck has to drain away from the water and grip under wet feet, so we slope it and finish it with a non-slick texture.
Old front steps that have pulled away from the porch or chipped are common here. We form new ones with even step heights so nobody catches a toe.
For a new garage, room addition or detached building, the slab foundation gets one pour and decades of use, so I plan the base and steel first.
When a structure needs more than a flat slab, we dig, form and pour the foundation to the approved plans and have it ready for inspection.
Small Colton businesses and rental properties often have lots that hold water and break up. We regrade, build a heavier base and pour concrete made for daily traffic.
Footings are the buried concrete under walls, posts and patio covers that carries the weight. We dig them to the depth the plans call for, on firm ground.
If a slab or porch has sunk and tipped toward the house, raising it can sometimes save a tear-out. I'll tell you straight which one yours needs.
We saw-cut old concrete for clean tear-outs, utility trenches and new joints, so the part that stays has a straight edge instead of a broken one.
What Colton ground asks of a slab
Concrete gives you one shot, so I'd rather tell you something hard before the pour than explain it after. Here's what that looks like.
I see every job first
I come out to look at every job and run the pour myself, so the one who quoted it is there.
Base first, finish second
We dig the base to firm ground and pack it, and if money's tight I'd trim the finish first.
Water runs away from you
Before we set forms, we check where water runs so the slab drains away from your house instead of pooling.
Joints cut on time
We cut control joints, shallow grooves that give the slab a planned place to crack, before it picks its own.
Licensed and insured on every job
We're licensed and fully insured, and you're welcome to see the paperwork when I come out, before you sign anything.
Questions we hear in Colton
How do I find out if my concrete driveway or patio needs a permit in Colton?
Call the city's Building & Safety Division at (909) 370-5079, because its permit list doesn't name driveways or patios either way and says it isn't complete. The division issues permits for building or enlarging a structure, reviews the plans and does the inspections, and its list does name work that often goes with concrete, like garages, carports, patio covers and walls. When your job needs a permit, we handle the application, line up the inspections and walk you through how the city's process goes.
Does a concrete retaining wall need a permit in Colton?
Yes, the city's permit list says every retaining wall needs one, whether you're building a new wall or tearing an old one down. Setback and height questions go to the city's Planning Division, so it pays to settle those before we pick where the wall goes. I'll look at your slope and what drainage the wall needs when I come out.
Does my concrete contractor need a Colton business license?
Yes, anyone doing work inside Colton city limits needs a City of Colton Business License, right down to a gardener working at a home. It matters for your permit too, because the city won't give a building permit final approval until every contractor on the job holds a city license. Ask anyone you're thinking of hiring whether theirs is in place.
How much can a contractor ask for up front on a home project in California?
No more than $1,000 or 10 percent of the contract price, whichever is less, under the rule set by the state contractors board. After that, every payment on a home improvement job has to be written into the contract and tied to work done or materials delivered. If someone wants a big check before anything shows up in your driveway, that's your sign to slow down.
How much does a new concrete driveway cost in Colton?
There's no honest single number until I've seen it, because a Colton driveway's price comes down to its size, the tear-out and the ground under it. Past those, a thicker slab with rebar for heavy trucks costs more, and so do stamping, color or a tight spot the truck can't reach. A plain broom finish, the light texture that gives tires and shoes grip, keeps it lower. I measure and check the ground when I come out, and you get your own figure from that.
What causes a new concrete slab to crack in Colton?
Most early cracks come from a base that was raked level instead of dug out and packed, joints cut too late or skipped, or a midday pour that leaves a weak, dusty top. Concrete shrinks as it cures, so nobody can honestly promise a slab won't crack, but we can control where it does by packing the base, cutting joints on time, pouring early and keeping the slab damp while it cures. On the river and fault-zone ground I mentioned above, that base work counts for even more.
Don't see your city? Call us
We're based in Moreno Valley and work across Riverside and San Bernardino counties. Choose your city if it's listed below, or call (951) 518-9186 if it isn't.
Talk to Bedrock about your Colton slab
Call (951) 518-9186 any day of the week, evenings included, or send the form and tell us what you'd like poured.